Special Belt Conveyors Belt Bend Inner radius 200mm to 1200mm Outer radius 600mm to 2200mm Stainless steel main frame Turning angle 90 or 180 degrees (other angles - phone) Belt Widths: 300mm, 400mm & 600mm. Speed Range 1.4 to 20m/min Load up to 10kg/sqm Food standards FDA/USDA Integral Belt Edges Used where small components could get under the belt

Conveyor length l T β Belt speed v m/s Belt sag y B mm Drum deflection y Tr mm Arc of contact at drive drum and idler β Opening angle at drive drum γ Incline (+) or decline (–) angle of conveyor α, δ Elongation at fitting ε % Drive efficiency η – Density of material conveyed ρ s kg/m3 Designation Symbol Unit Terminology 2

Belt Widths The belt widths are as follows: 18, 24, 30, 36, 42, 48, 54, 60, 72, 84, and 96 inches. The width of the narrower belts may be governed by the size of lumps to be handled. Belts must be wide enough so that any combination of prevailing lumps and finer material does not load the lumps too close to the edge of the conveyor belt

With conveyor aspect ratio (conveyor length to belt width) in excess of about 5 to 1 and in installations with reversing operations, it is advisable to crown both, head pulley and tail pulley. Following this method, a correctly aligned belt can be maintained in its central position as long as there is no excessive deflection of the pulleys

1/2” 1 1/4” 2 1/2” 12” 8 1/2”. E 66” to 78” belts. 3/8” 1 1/4” 2 1/2” 11” 5 1/16” 11/16” x 1” SLOT 11/16” SLOT. 2 11/16” 4” 6” 1 1/2” 9/16” x 1” SLOT 3/16”. REISION E & IDER RIGS RESERED 59. 7” 12” 9” 10” 13/16” SLOTS 1 3/4”. MOUNTING DETAILS FOOTPADS & BRACKETS. 8” 3 9/16” 4 1/2” 2 11/16” 3/16” 11/16” SLOT 1 1/4”

Components of a belt conveyor. 1. Aluminium profile conveyor belt supports. 2. Driving unit. 2.1 Driving unit 2.2 Motor bracket 2.3 Counter-bearings 2.4 Drive (electrical) 3. Extremity unit. 3.1 Extremity pulley 3.2 Extemity parts (such as clamping straps) In addition, a series of add-on modules are available, such as lateral guides, stands, etc

5 CONVEYOR PULLEY SELECTION GUIDE Pulley/Core Diameter – The outside diameter of the cylindrical body of a conveyor pulley, without coating. Finish Diameter – The outside diameter of a coated pulley (core diameter + 2 times the coating/wrap thickness). Face Width – The length of a pulley’s cylindrical body.This area is intended to act as the contact surface for the conveyor belt

Belt Conveyors are also a great option to move products through elevations. Incline Belt Conveyors from low to high and Decline Belt Conveyors from high to low. This manual is short, with quick and easy reading paragraphs, very practical for calculations of belt, chain conveyors and mechanical miscellaneous, in the metric and imperial system

With conveyor aspect ratio (conveyor length to belt width) in excess of about 5 to 1 and in installations with reversing operations, it is advisable to crown both, head pulley and tail pulley. Following this method, a correctly aligned belt can be maintained in its central position as long as there is no excessive deflection of the pulleys

Belt Widths The belt widths are as follows: 18, 24, 30, 36, 42, 48, 54, 60, 72, 84, and 96 inches. The width of the narrower belts may be governed by the size of lumps to be handled. Belts must be wide enough so that any combination of prevailing lumps and finer material does not load the lumps too close to the edge of the conveyor belt

May 08, 2021 May 08, 2021 Duck for conveyor belting ordinarily weighs 28 to 42 ounces and the plys from 3 to 8 depending on the factors of length of conveyor, width of belt, size of head and tail pulleys and the weight and character of material to be handled

Steel construction and greater horsepower give these conveyors higher capacities and speeds than standard Ready-to-Run Mini Belt Conveyors. Build-Your-Own Flow Rails Configure wheels where you need them on these economical rails that you can cut to length